How to Use TaoTronics LED Desk Lamp and Floor Lamp

How to Use TaoTronics LED Desk Lamp?

  1. Power On / Off ·

Connect the lamp to a wall outlet using the included power adapter, tap on the Power Button to turn on the lamp.

Press and hold the Power Button for 2 seconds to turn off the lamp.

  1. Brightness Control

Tap or slide across the Light Brightness Slider to adjust the light brightness.

  1. Color Temperature Adjustment

Tap the Color Temperature Button to adjust the color temperature.

  1. Memory Function

Tap and hold the Power Button to turn off the lamp. It will remember the light brightness and temperature of last use when turned on again.

  1. Timer Function

Tap the Timer button and the indicator will slowly flashes 3 times to start timing. The lamp will automatically turn off in 60 minutes. Tap again in timer mode to cancel the timer setting. The LED indicator will flash once.

  1. Favorite Function

When the lamp is on, tap and hold the Favorite Setting button for 2 seconds. The indicator will flash 3 times and the current color temperature and brightness will be set as your favorite. Each time the lamp is turned on, tap on the button once to activate your favorite setting. Tap and hold again for 2 seconds to erase and set a new favorite.

  1. Night Light Function

When the lamp is on, tap the Night mode button until the indicator slowly flashes 3 times to light up the night light. Tap either the night mode button or the on/off button to turn off the night light. In Night Light mode, tap the Timer button to set or cancel the 60-minute timer.

Note: The night light and main lamp will not light up at the same time.

  1. USB Port

Use the USB port to charge a smartphone, tablet, e-reader or another USB charging device.

How to Use TaoTronics LED Desk Lamp Wireless Charging Function?

Place your phone with wireless charging functionality onto the charging pad, charging will start automatically. The wireless charging indicator will stay solid blue when charging and turn off once your phone is fully charged.

Note:

  1. If charging does not occur, adjust the phone so its receiver can be detected.
  2. Please note that different model phones have their receivers in different positions. Please align the charging coil of your phone with that of the charging pad to achieve the fast charging.

How to Troubleshoot the TaoTronics LED Desk Lamp?

Problem

Possible Cause

Solution

The lamp does not light up

No power supply

Correctly plug in the power adapter

The lamp is not turned on

Refer to the How to Use section

The touch panel is not responsive

Hands are wet

Touch the panel with dry hands

Voltage fluctuation causing panel failure 

Disconnect power to restart the lamp

LED failure

LED component failed

Please contact the TaoTronics Support Team

Bad smell

Power adapter failed

Please contact the TaoTronics Support Team

Short circuit 

Please contact the TaoTronics Support Team

How Long are the TaoTronics LED Desk Lamp Warranty?

TaoTronics products are covered by a 12-month limited warranty from the date of its original purchase.

If any problems occur, please contact our support team. We can only provide after sales service for products that are sold by TaoTronics or TaoTronics authorized retailers and distributors.

If you have purchased your unit from a different place, please contact your seller for return and warranty issues.

What Should You Pay Attention to When Using TaoTronics LED Desk Lamp?

  1. Do not repair, disassemble, or modify under any circumstance.
  2. Place on flat and secure surface.
  3. Do not use the lamp with frayed or damaged electrical cords.
  4. Please keep all the components of the lamp dry and clean.
  5. Clean with soft and dry cloth and do not use solvents or cleaning solutions.
  6. Avoid any extreme heat sources or direct sunlight.
  7. Use the supplied AC power adapter only.
  8. Do not touch electrical parts with wet hands.
  9. Unplug the adapter when not in use.
  10. Never overload electrical circuits as it may cause electrical shock or fire.

How Should You Do if the TaoTronics LED Desk Lamp Cause Harmful Interference to Radio Communication?

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
  4. Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

How to Assemble and Disassemble TaoTronics LED Floor Lamp?

Assemble and Disassemble TaoTronics LED Floor Lamp

Note:

  1. When connecting the sections, rotate in opposite directions with both hands and do not screw with too much force.
  2. You can choose to use different numbers of sections for different purposes and scenes. To disassemble, follow the assembly steps as above in the reverse order.

How to Use TaoTronics LED Floor Lamp?

Use TaoTronics LED Floor Lamp
  1. Standby Mode

Connect the lamp to a power source and it will enter standby mode. The Power Indicator on the Power Button will light up.

  1. Power On / Off

Tap the Power Button to turn the lamp on / off.

  1. Color Temperature / Brightness Adjustment

Tap the Color Temperature Button to cycle through 3 color temperature settings. Tap the Brightness + / - Button to adjust 5 levels of brightness in each color temperature setting.

  1. Auto Shutoff Timer

Press and hold the Power / Timer Button for 2 seconds, the Power Indicator will start to flicker and activate a 60 minutes auto shut-off timer. Repeat this operation or press the Power / Timer Button to turn off the timer.

  1. Adjust the Lamp Head

Note: Please do not turn the lamp head for over 180° to avoid damaging the gooseneck

What Should You Pay Attention to When Using TaoTronics LED Floor Lamp?

  1. Please do not dismantle the product by yourself, always ask a professional electrician or authorized technician for repairs.
  2. If you smell a bad odor or anything unusual, please turn off the unit immediately.
  3. Please do not remove the power cable with wet hands as it may cause an electric shock.
  4. Do not put this unit near extreme heat sources, moisture, or corrosive substances.
  5. Clean the lamp with a dry cloth when needed.
  6. Please store the lamp in a dry and shady place if not being used for a long period of time.
  7. Use the original power adapter to power the lamp. A wrong input may damage the lamp.