Very week
Bought for my wife and she loves it
Beautiful noiseless still testing
Connect the lamp to a wall outlet using the included power adapter, tap on the Power Button to turn on the lamp.
Press and hold the Power Button for 2 seconds to turn off the lamp.
Tap or slide across the Light Brightness Slider to adjust the light brightness.
Tap the Color Temperature Button to adjust the color temperature.
Tap and hold the Power Button to turn off the lamp. It will remember the light brightness and temperature of last use when turned on again.
Tap the Timer button and the indicator will slowly flashes 3 times to start timing. The lamp will automatically turn off in 60 minutes. Tap again in timer mode to cancel the timer setting. The LED indicator will flash once.
When the lamp is on, tap and hold the Favorite Setting button for 2 seconds. The indicator will flash 3 times and the current color temperature and brightness will be set as your favorite. Each time the lamp is turned on, tap on the button once to activate your favorite setting. Tap and hold again for 2 seconds to erase and set a new favorite.
When the lamp is on, tap the Night mode button until the indicator slowly flashes 3 times to light up the night light. Tap either the night mode button or the on/off button to turn off the night light. In Night Light mode, tap the Timer button to set or cancel the 60-minute timer.
Note: The night light and main lamp will not light up at the same time.
Use the USB port to charge a smartphone, tablet, e-reader or another USB charging device.
Place your phone with wireless charging functionality onto the charging pad, charging will start automatically. The wireless charging indicator will stay solid blue when charging and turn off once your phone is fully charged.
Note:
Problem |
Possible Cause |
Solution |
The lamp does not light up |
No power supply |
Correctly plug in the power adapter |
The lamp is not turned on |
Refer to the How to Use section |
|
The touch panel is not responsive |
Hands are wet |
Touch the panel with dry hands |
Voltage fluctuation causing panel failure |
Disconnect power to restart the lamp |
|
LED failure |
LED component failed |
Please contact the TaoTronics Support Team |
Bad smell |
Power adapter failed |
Please contact the TaoTronics Support Team |
Short circuit |
Please contact the TaoTronics Support Team |
TaoTronics products are covered by a 12-month limited warranty from the date of its original purchase.
If any problems occur, please contact our support team. We can only provide after sales service for products that are sold by TaoTronics or TaoTronics authorized retailers and distributors.
If you have purchased your unit from a different place, please contact your seller for return and warranty issues.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Note:
Connect the lamp to a power source and it will enter standby mode. The Power Indicator on the Power Button will light up.
Tap the Power Button to turn the lamp on / off.
Tap the Color Temperature Button to cycle through 3 color temperature settings. Tap the Brightness + / - Button to adjust 5 levels of brightness in each color temperature setting.
Press and hold the Power / Timer Button for 2 seconds, the Power Indicator will start to flicker and activate a 60 minutes auto shut-off timer. Repeat this operation or press the Power / Timer Button to turn off the timer.
Note: Please do not turn the lamp head for over 180° to avoid damaging the gooseneck