How to Use TaoTronics Bluetooth Headphones | Manual & Troubleshooting

How to Charge TaoTronics Bluetooth Headphone?

Connect the charging port to any USB charging adapter or active computer USB port.
Charging will start automatically with the LED indicator turning red.
The headphones are fully charged when the LED indicator turns blue.

Note:

Make sure the battery is fully charged before putting the headphones away for storage.
Charge the headphones at least once every 3 months when not using for a long time.

How to Pair TaoTronics Bluetooth Headphone?

Make sure the headphones and your Bluetooth® device are next to each other (within 3 feet / 1 meter).
The first time you use the headphones, press and hold the Multifunction Button until the LED indicator ﬂashes red and blue alternately. Now the headphones are in pairing mode.
Activate Bluetooth® on your phone and search for nearby Bluetooth® connections. Find TaoTronics Bluetooth Headphone Type in the search results and connect. Once connected, the LED indicator will ﬂash blue.

Note: Automatic Re-pairing: The Bluetooth headset can remember devices paired previously.

You may simply turn on the headset and the device (with Bluetooth activated), and they will connect to the last connected device automatically without going into the pairing mode.

How to Do if the Headphone Can’t Pair with the Bluetooth Device?

If the headphones cannot pair with your Bluetooth device, clear the pairing history as below:

Turn on the Bluetooth headphones and bring it into pairing mode, the indicator will flash red and blue alternatively.
Press and hold the Volume + / - Buttons at the same time for 7 seconds until the LED indicator flashes purple once and 2 beep sounds are heard.
You can just pair the headphones just like when they are new

How to Clear TaoTronics Bluetooth Headphone Pairing History?

If the headset fails to pair with your Bluetooth device clear the pairing history by pressing and holding the Multifunction and Volume - Buttons simultaneously when the headset is on until the LED indicator ﬂashes red and blue at the same time indicating clearing successfully. Then re-pair your Bluetooth device as instructed in Pairing.
If you want to pair the headset with another device when already paired, deactivate the Bluetooth function on the paired device or remove TaoTronics Bluetooth Headphone type from the Bluetooth list.

How to Active the ANC Function of TaoTronics ANC Bluetooth Headphone?

Switch the ANC Button from OFF to ANC to activate the noise cancellation function.

Control Function

Function	Operation
Power on / off	Press and hold the Multifunction Button for 2 seconds
Redial	Press the Power Button twice
Voice Control	Press and hold the Multifunction Button for 1 second
Answer Calls	When there is an incoming call, press the Multifunction Button once
Reject Calls	When there is an incoming call, press and hold the Multifunction Button for 1 second
End Calls	During a call, press the Multifunction Button once
Mute Calls	During a call, press the Microphone Button once. Press again to normal calls
Transfer Calls	During a call, press and hold the Multifunction Button for 1 second to transfer the call between the phone and the headset
Second Call	When there is a second incoming call (B) in the course of an ongoing call (A), • Press the Multifunction Button once to answer B and hang up A · Press the Multifunction Button twice to answer B and on-hold A · Press and hold the Multifunction Button for 2 seconds to reject B During a second call, press the Multifunction Button twice to transfer calls between A and B
Volume + /-	Press the Volume + / - Button
Pause / Play	Press the Multifunction Button
Previous / Next Track	Press and hold the Volume + / - Button
ANC On / Off	Press and hold the ANC Button to turn on / off the ANC function with the ANC indicator ﬂashing orange / turning off
ANC Mode	When ANC is activated, each time you press the ANC Button once, the three modes (Travel Mode, Ofﬁce Mode, Ambient Mode) are switched alternately.

How to Do if the Bluetooth Headphone Does Cause Harmful Interference to Radio or Television Reception?

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Your bag